Differences

This shows you the differences between two versions of the page.

--- en:iot-open:introductiontoembeddedprogramming2:cppfundamentals:digital_io [2023/07/08 01:38] – pczekalski
+++ en:iot-open:introductiontoembeddedprogramming2:cppfundamentals:digital_io [2023/11/23 12:21] (current) – pczekalski
@@ Line 1: / Line 1: @@
+====== Digital ports, reading inputs, outputting data ======
+{{:en:iot-open:czapka_b.png?50| General audience classification icon }}{{:en:iot-open:czapka_m.png?50| General audience classification icon }}{{:en:iot-open:czapka_e.png?50| General audience classification icon }}\\
+Every microcontroller has many pins that can be used to connect external electronic elements. In the examples shown in previous chapters, LED was used. Such LED can be connected to a chosen General Purpose Input Output (GPIO) pin and can be controlled by setting a HIGH or LOW state. Below are some details of the functions that allow the manipulation of GPIOs using the Arduino framework. In the next chapter, analogue signals will be considered.
+==== Digital I/O ====
+Microcontrollers' digital inputs and outputs allow for connecting different sensors and actuators to the board. Digital signals can take two values – //HIGH//(1) or //LOW//(0). These states correspond to high voltage (usually corresponding to the power supply voltage of the microcontroller) and low voltage (around 0V). These inputs and outputs are used in applications when the signal can have only two states.
+<note important>
+Notice that the voltage the microcontroller is powered with can be different (usually lower) than the voltage provided directly to the board. For example, the ATmega microcontroller on the Arduino Uno board is powered with 5V, while the board itself can be powered from an external source providing 7-12V. Other microcontrollers require different voltages, e.g. Espressif 3.3V. Refer to the device manual for a valid range of voltages.
+</note>
+**pinMode()**
+The function //pinMode()// is essential to indicate whether the specified GPIO pin will behave like an input or an output and may also control special features. This function does not return any value. Usually, the mode of a pin is set in the //setup()// function of a program – only once, during program initialisation.
+The syntax of a function is the following:
+<code c>
+pinMode(pin, mode);
+</code>
+The parameter //pin// is the number of the pin.
+The parameter //mode// can have three different values – //INPUT//, //OUTPUT//, //INPUT_PULLUP//, depending on whether the pin will be used as an input or an output. The //INPUT_PULLUP// mode turns on the internal pull-up resistor between the power supply and the pin itself. It ensures that if the pin remains unconnected, the logic state will be stable and equal to HIGH. More about pull-up resistors can be found on the Arduino homepage ((https://www.arduino.cc/en/Tutorial/DigitalPins)).
+<note important> Most MCUs are pretty flexible in the configuration and use of GPIOS. There are some special GPIOs, however. Some of them cannot work as inputs or outputs or do not have internal pull-up resistors to enable them. Refer to the technical documentation of the hardware you use before setting up your configuration and external devices like sensors, buttons and applications. Some of the GPIOs are also predefined for communication protocols such as Serial, I2C, SPI, etc.</note>
+**digitalWrite()**
+The function //digitalWrite()// writes a //HIGH// or //LOW// value to the pin. This function is used for digital pins, such as turning on/off LEDs. This function also does not return any value.
+The syntax of a function is the following:
+<code c>
+digitalWrite(pin, value);
+</code>
+The parameter //pin// is the number of the pin.
+The parameter //value// can take values //HIGH// or //LOW//. If the mode of the pin is set to the //OUTPUT//, the //HIGH// sets voltage to power supply voltage and //LOW// to 0 V.
+Using this function for pins set to have the INPUT mode is also possible. In this case, //HIGH// or //LOW// values enable or disable the internal pull-up resistor.
+**digitalRead()**
+The function //digitalRead()// works in the opposite direction than the function //digitalWrite()//. It reads the pin's value that can be either //HIGH// or //LOW// and returns it.
+The syntax of a function is the following:
+<code c>
+digitalRead(pin);
+</code>
+The parameter //pin// is the number of the pin.
+On the opposite of the functions viewed before, this one has the return type, and it can take a value of //HIGH// or //LOW//.
+In the code below, the button connected to pin 3 controls the LED connected to pin 4.
+<code c>
+#define BUTTON_pin 3
+#define LED_pin 4
+void setup() {
+  pinMode(LED_pin, OUTPUT);
+  pinMode(BUTTON_pin, INPUT_PULLUP);
+}
+bool state;
+void loop() {
+  state = digitalRead(BUTTON_pin); //reading digital state of the input
+  digitalWrite(LED_pin, state);    //writing state back to the output
+}
+</code>